From the free quote to the final rinse, pressure washing for concrete in Ripon, WI follows a simple process: inspect, protect, clean, rinse and check. With concrete, the right approach is pressure wash with a surface cleaner.
How we clean it
Cleaning solution: A degreaser for oil spots and a pre-treatment for organic growth; post-treatment slows regrowth.
What to know about cleaning concrete
Plain broom-finish concrete is the surface pressure washing is made for. A rotary surface cleaner gives an even finish without the stripes a wand leaves, and hot water helps with grease and oil.
Avoid: Holding a narrow tip close to the surface, which etches lines into the cream layer of the concrete.
How often: Every year, or every 6 months in shaded, damp spots.
Is it time for pressure washing for concrete?
- Driveway or walkways look dark, gray or streaky
- Green or black growth in shaded areas and along edges
- Slippery surfaces after rain
- Oil, rust or tire marks you can't scrub out
- You're getting ready to sell, seal or paint
Where the grime comes from
- Dirt and pollen that settle into the pores of concrete
- Mold, mildew and algae in damp, shaded spots
- Oil and fluid drips from vehicles
- Rust from sprinklers, furniture and fertilizer
- Tire marks and general foot traffic
Easy upkeep between cleanings
- Sweep off leaves and loose debris so they don't stain
- Blot fresh oil drips with cat litter or an absorbent right away
- Point sprinklers away from walls and walkways to cut down on rust and hard-water stains
- Rinse pollen off with a garden hose during heavy pollen season
Not sure what you're looking at? The free stain identifier and safe pressure guide explain each stain and surface.
What can go wrong with DIY pressure washing
- Etched lines and 'zebra stripes' from holding a narrow tip too close
- Water forced into window frames, door sills and siding laps
- Damaged plants and lawns from chemical runoff
- Injuries: a zero-degree tip can cut skin, and wet surfaces are slippery
Our process for pressure washing for concrete
- Walk the property and note surfaces, stains and anything fragile
- Protect plants, outlets, lights and doors, and move small items
- Pre-treat organic growth and degrease oil spots
- Clean with the right pressure and a surface cleaner for even results
- Rinse, post-treat to slow regrowth, and walk the job with you
How much does pressure washing for concrete cost?
What moves the price:
- Size: square footage of siding, roof or flatwork
- Condition: heavy growth, old stains and peeling finishes take longer
- Access: number of stories, roof pitch, slopes and how close we can park
- Add-ons: sealing, gutter brightening and other services done in the same trip
These are typical U.S. ranges, not a quote. You get an exact price before any work starts. For a quick estimate, try the pressure washing cost calculator.
Other services for concrete
- Driveway Cleaning for Concrete
- Sidewalk & Walkway Cleaning for Concrete
- Patio Cleaning for Concrete
- Pool Deck Cleaning for Concrete
- Concrete Sealing for Concrete
- Rust Stain Removal for Concrete
- Oil Stain Removal for Concrete
- Graffiti Removal for Concrete
- Gum Removal for Concrete
- Efflorescence Removal for Concrete
- Exterior Mold & Mildew Removal for Concrete
- Commercial Pressure Washing for Concrete
- Parking Lot & Garage Cleaning for Concrete
- HOA & Apartment Pressure Washing for Concrete
Serving Ripon, WI and nearby towns
Freeze-thaw cycles and deicing salt are hard on concrete in Wisconsin. Cleaning it in spring and sealing it before winter reduces how much water and salt soak in, which is what causes surface flaking (spalling).
Crews serve all of Ripon (ZIP code 54971), plus Berlin (10.2 mi), Omro (14.4 mi), Waupun (15.4 mi) and North Fond du Lac (17.7 mi). Call (555) 010-0000 for a free quote in Ripon.
Pressure Washing for Concrete: frequently asked questions
How much does pressure washing for concrete cost in Ripon, WI?
Pressure Washing for Concrete typically costs $150-$600 for a typical home's driveway, walkways and patio, and usually takes 1-4 hours. The exact price depends on the size and condition, and you get it before any work starts. Call (555) 010-0000 for a free quote.
Do you use high pressure for pressure washing for concrete?
For concrete: usually 2,500-3,500 PSI with a rotary surface cleaner for even results. What we avoid: holding a narrow tip close to the surface, which etches lines into the cream layer of the concrete. We keep the pressure even and controlled, with the right tools for the surface.
Is pressure washing for concrete safe for my plants and pets?
We pre-wet plants and lawns, keep cleaning solutions diluted to what the surface needs, and rinse landscaping again when we finish. Keep pets and children inside until surfaces are rinsed and dry.
How often should I schedule pressure washing for concrete?
Every year, or every 6 months in shaded, damp spots. Shade, nearby trees, humidity and heavy traffic mean more frequent cleaning; sunny, dry spots can go longer. Our free cleaning frequency tool gives a recommendation for your climate.
What if it rains on the day?
Light rain doesn't stop most washing, but heavy rain, high wind, lightning and freezing temperatures do. If the weather isn't right, we reschedule at no charge. Our work is backed by a satisfaction guarantee.